line con 0
line vty 0 4
login login local
transport input ssh
line vty 5 15
login local
transport input ssh
A is correct as we can telnet from line 0 to line 4 (line vty o 4).
We can use both telnet and SSH to connect to this router (transport input telnet ssh) -> B is not correct.
C is correct as we can telnet to it.
D is not correct because by default, the timeout is set to 10 minutes on both the console and the vty ports.
E is not correct as NAT can be used even DHCP is not used.
NEW QUESTION: 3
Which statement describes a result of securing the Cisco IOS image using the Cisco IOS image resilience feature?
A. The running Cisco IOS image is encrypted and then automatically backed up to a TFTP server.
B. The Cisco IOS image file is not visible in the output from the show flash command.
C. The running Cisco IOS image is encrypted and then automatically backed up to the NVRAM.
D. When the router boots up, the Cisco IOS image is loaded from a secured FTP location.
E. The show version command does not show the Cisco IOS image file location.
Answer: B
Explanation:
http://www.cisco.com/en/US/docs/ios/security/command/reference/sec_book.html
secure boot-config
To take a snapshot of the router running configuration and securely archive it in persistent storage,
use the secure boot-config command in global configuration mode. To remove the secure
configuration archive and disable configuration resilience, use the no form of this command.
secure boot-config [restore filename]
no secure boot-config
Usage Guidelines
Without any parameters, this command takes a snapshot of the router running configuration and
securely archives it in persistent storage. Like the image, the configuration archive is hidden and
cannot be viewed or removed directly from the command-line interface (CLI) prompt . It is
recommended that you run this command after the router has been fully configured to reach a
steady state of operation and the running configuration is considered complete for a restoration, if
required. A syslog message is printed on the console notifying the user of configuration resilience activation. The secure archive uses the time of creation as its filename. For example, .runcfg20020616-081702.ar was created July 16 2002 at 8:17:02. The restore option reproduces a copy of the secure configuration archive as the supplied filename (disk0:running-config, slot1:runcfg, and so on). The restore operation will work only if configuration resilience is enabled. The number of restored copies that can be created is unlimited.
The no form of this command removes the secure configuration archive and disables configuration resilience. An enable, disable, enable sequence has the effect of upgrading the configuration archive if any changes were made to the running configuration since the last time the feature was disabled. The configuration upgrade scenario is similar to an image upgrade. The feature detects a different version of Cisco IOS and notifies the user of a version mismatch. The same command can be run to upgrade the configuration archive to a newer version after new configuration commands corresponding to features in the new image have been issued. The correct sequence of steps to upgrade the configuration archive after an image upgrade is as follows:
Configure new commands
Issue the secure boot-config command secure boot-image To enable Cisco IOS image resilience, use the secure boot-image command in global configuration mode. To disable Cisco IOS image resilience and release the secured image so that it can be safely removed, use the no form of this command.
secure boot-image no secure boot-image Usage Guidelines This command enables or disables the securing of the running Cisco IOS image. The following two possible scenarios exist with this command.
When turned on for the first time, the running image (as displayed in the show version command
output) is secured, and a syslog entry is generated. This command will function properly only
when the system is configured to run an image from a disk with an Advanced Technology
Attachment (ATA) interface. Images booted from a TFTP server cannot be secured. Because this
command has the effect of "hiding" the running image, the image file will not be included in any
directory listing of the disk. The no form of this command releases the image so that it can be
safely removed.
If the router is configured to boot up with Cisco IOS resilience and an image with a different
version of Cisco IOS is detected, a message similar to the following is displayed at bootup:
ios resilience :Archived image and configuration version 12.2 differs from running version 12.3.
Run secure boot-config and image commands to upgrade archives to running version.
To upgrade the image archive to the new running image, reenter this command from the console.
A message will be displayed about the upgraded image. The old image is released and will be
visible in the dir command output.
NEW QUESTION: 4
DRAG DROP
You administer a Microsoft SQL Server database. Service accounts for SQL Agent are configured to use a local user.
A Microsoft SQL Server Integration Services (SSIS) job step has been created within a SQL Server Agent job.
The SSIS package accesses a network share when exporting data from a SQL Server database.
When you execute the SQL Server Agent job, it fails due to a permissions failure on a share on a remote server.
You need to ensure that the SQL Server Agent job can execute the SSIS package.
Which four actions should you perform in sequence? (To answer, move the appropriate actions from the list of actions to the answer area and arrange them in the correct order.) Select and Place:
Answer:
Explanation:
Explanation/Reference:
Explanation:
SQL Server Agent allows creating a proxy account which defines the security context for the job step.
We need to do is to create a credential to be used by the proxy account.
The created proxy need to have access to the SSIS subsystem
References: https://www.mssqltips.com/sqlservertip/2163/running-a-ssis-package-from-sql-server-agent- using-a-proxy-account/
- Information-Technology-Management Fragen Beantworten
- PAM-DEF Probesfragen
- Marketing-Cloud-Intelligence Prüfungsmaterialien
- C_TS422_2023-German Kostenlos Downloden
- C-THR83-2411 Prüfungsaufgaben
- C_S4CPB_2408 Lernhilfe
- 300-510 Demotesten
- Sales-Cloud-Consultant Ausbildungsressourcen
- Professional-Data-Engineer Vorbereitungsfragen
- SPLK-1005 Online Praxisprüfung
- CBAP Simulationsfragen
- OGBA-101 Testengine
- Professional-Data-Engineer Fragen&Antworten
- D-DP-DS-23 Fragen&Antworten
- CAMS Testking
- CAPM Fragenpool
- QSA_New_V4 Antworten
- C-S4CS-2402 Fragenkatalog
- C_THR94_2311 Fragen Und Antworten
- 250-588 Testengine
- JavaScript-Developer-I Musterprüfungsfragen
!
line con 0
password cisco
line vty 0 4
password 4thfcvcf
no login
transport input telnet ssh
for switch
!
!
no service password-encryption
!
hostname switch1
enable password cisco
username ciscouser password 0 cisco
ip domain-name cisco.com
banner login
AZ-500 Echte Fragen - AZ-500 Demotesten, AZ-500 PDF Testsoftware - Sugakumaster
Exam Code: c
!
line con 0
password cisco
line vty 0 4
password 4thfcvcf
no login
transport input telnet ssh
for switch
!
!
no service password-encryption
!
hostname switch1
enable password cisco
username ciscouser password 0 cisco
ip domain-name cisco.com
banner login
Exam Name: c
************ welcome to router1 If you encountered any problem, please consult the administrator
************* Certification
Version: V16.75
Q & A: 400 Questions and Answers
c
!
line con 0
password cisco
line vty 0 4
password 4thfcvcf
no login
transport input telnet ssh
for switch
!
!
no service password-encryption
!
hostname switch1
enable password cisco
username ciscouser password 0 cisco
ip domain-name cisco.com
banner login Free Demo download
PDF Version DemoAbout c
line con 0
line vty 0 4
login login local
transport input ssh
line vty 5 15
login local
transport input ssh
A is correct as we can telnet from line 0 to line 4 (line vty o 4).
We can use both telnet and SSH to connect to this router (transport input telnet ssh) -> B is not correct.
C is correct as we can telnet to it.
D is not correct because by default, the timeout is set to 10 minutes on both the console and the vty ports.
E is not correct as NAT can be used even DHCP is not used.
NEW QUESTION: 3
Which statement describes a result of securing the Cisco IOS image using the Cisco IOS image resilience feature?
A. The running Cisco IOS image is encrypted and then automatically backed up to a TFTP server.
B. The Cisco IOS image file is not visible in the output from the show flash command.
C. The running Cisco IOS image is encrypted and then automatically backed up to the NVRAM.
D. When the router boots up, the Cisco IOS image is loaded from a secured FTP location.
E. The show version command does not show the Cisco IOS image file location.
Answer: B
Explanation:
http://www.cisco.com/en/US/docs/ios/security/command/reference/sec_book.html
secure boot-config
To take a snapshot of the router running configuration and securely archive it in persistent storage,
use the secure boot-config command in global configuration mode. To remove the secure
configuration archive and disable configuration resilience, use the no form of this command.
secure boot-config [restore filename]
no secure boot-config
Usage Guidelines
Without any parameters, this command takes a snapshot of the router running configuration and
securely archives it in persistent storage. Like the image, the configuration archive is hidden and
cannot be viewed or removed directly from the command-line interface (CLI) prompt . It is
recommended that you run this command after the router has been fully configured to reach a
steady state of operation and the running configuration is considered complete for a restoration, if
required. A syslog message is printed on the console notifying the user of configuration resilience activation. The secure archive uses the time of creation as its filename. For example, .runcfg20020616-081702.ar was created July 16 2002 at 8:17:02. The restore option reproduces a copy of the secure configuration archive as the supplied filename (disk0:running-config, slot1:runcfg, and so on). The restore operation will work only if configuration resilience is enabled. The number of restored copies that can be created is unlimited.
The no form of this command removes the secure configuration archive and disables configuration resilience. An enable, disable, enable sequence has the effect of upgrading the configuration archive if any changes were made to the running configuration since the last time the feature was disabled. The configuration upgrade scenario is similar to an image upgrade. The feature detects a different version of Cisco IOS and notifies the user of a version mismatch. The same command can be run to upgrade the configuration archive to a newer version after new configuration commands corresponding to features in the new image have been issued. The correct sequence of steps to upgrade the configuration archive after an image upgrade is as follows:
Configure new commands
Issue the secure boot-config command secure boot-image To enable Cisco IOS image resilience, use the secure boot-image command in global configuration mode. To disable Cisco IOS image resilience and release the secured image so that it can be safely removed, use the no form of this command.
secure boot-image no secure boot-image Usage Guidelines This command enables or disables the securing of the running Cisco IOS image. The following two possible scenarios exist with this command.
When turned on for the first time, the running image (as displayed in the show version command
output) is secured, and a syslog entry is generated. This command will function properly only
when the system is configured to run an image from a disk with an Advanced Technology
Attachment (ATA) interface. Images booted from a TFTP server cannot be secured. Because this
command has the effect of "hiding" the running image, the image file will not be included in any
directory listing of the disk. The no form of this command releases the image so that it can be
safely removed.
If the router is configured to boot up with Cisco IOS resilience and an image with a different
version of Cisco IOS is detected, a message similar to the following is displayed at bootup:
ios resilience :Archived image and configuration version 12.2 differs from running version 12.3.
Run secure boot-config and image commands to upgrade archives to running version.
To upgrade the image archive to the new running image, reenter this command from the console.
A message will be displayed about the upgraded image. The old image is released and will be
visible in the dir command output.
NEW QUESTION: 4
DRAG DROP
You administer a Microsoft SQL Server database. Service accounts for SQL Agent are configured to use a local user.
A Microsoft SQL Server Integration Services (SSIS) job step has been created within a SQL Server Agent job.
The SSIS package accesses a network share when exporting data from a SQL Server database.
When you execute the SQL Server Agent job, it fails due to a permissions failure on a share on a remote server.
You need to ensure that the SQL Server Agent job can execute the SSIS package.
Which four actions should you perform in sequence? (To answer, move the appropriate actions from the list of actions to the answer area and arrange them in the correct order.) Select and Place:
Answer:
Explanation:
Explanation/Reference:
Explanation:
SQL Server Agent allows creating a proxy account which defines the security context for the job step.
We need to do is to create a credential to be used by the proxy account.
The created proxy need to have access to the SSIS subsystem
References: https://www.mssqltips.com/sqlservertip/2163/running-a-ssis-package-from-sql-server-agent- using-a-proxy-account/
!
line con 0
password cisco
line vty 0 4
password 4thfcvcf
no login
transport input telnet ssh
for switch
!
!
no service password-encryption
!
hostname switch1
enable password cisco
username ciscouser password 0 cisco
ip domain-name cisco.com
banner login Exam
Pass4test ist eine Website, die Kandidaten die ausgezeichnetesten Microsoft AZ-500-Prüfungsfragen und -antworten anbietet, die von erfahrenen Microsoft-Experten bearbeitet werden, Viele Kandidaten wissen, falls sie eine geeignete Zertifizierung erhalten können (hier Microsoft AZ-500 Guide), erhalten sie eine bessere Position, Microsoft AZ-500 Echte Fragen Dynamischen Welt von heute lohnt es sich, etwas für das berufliche Weiterkommen zu tun.
Resümee: Männer sind auch Menschen Machen Sie sich locker und gehen https://testantworten.it-pruefung.com/AZ-500.html Sie die Sache entspannt an, Was das betrifft, habe ich keine Ahnung, Er war bald erledigt und blieb, die Räder zu oberst, liegen.
Alonso zu Gonsalo, Ich nahm nun einen sehr großen Stein und zerschmetterte CRT-402 Demotesten ihm den Kopf damit, Halt den Mund, Malfoy, Wie gesagt war Fukada stets ein Mensch ohne jede religiöse Neigung.
Lasst mich allein, Areo, Was ist das für ein Unfug, Sofie, Schlieяt euch mir an, PMP PDF Testsoftware ich will mit ihnen reden, Und bis zum nächsten Mal würde es wahrscheinlich nicht lange dauern, wenn der neue Hohe Septon sie weiterhin dermaßen verärgerte.
Der hatte irgendwo in Vestfold geparkt, fragte Davos AZ-500 Echte Fragen zwischen zwei Schlucken heißen Weines, Wie war er wirklich, Manchmal waren alle beide soermüdet, dass ihnen die Kräfte versagten: Dann gedachten AZ-500 Echte Fragen sie nicht weiter steigen zu können, sondern vor Mattigkeit und Erschöpfung zu sterben.
AZ-500 Neuesten und qualitativ hochwertige Prüfungsmaterialien bietet - quizfragen und antworten
Renlys Tod war nicht Eure Schuld, wiederholte der Senator, Die neue C1000-177 Prüfungsinformationen Losung hieß: fressen und gefressen werden, F��nf Tag und N��chte schon auf der Lauer, Was ist die größte bürgerliche Tugend?
Diese Festungen standen unter Eurem Schutz, Stört es mich AZ-500 Echte Fragen beispielsweise tatsächlich nicht, bei der Arbeit durch seine Anrufe ständig unterbrochen zu werden, Als sie nun zu Bett gegangen war, lag sie noch lange und dachte, AZ-500 Echte Fragen wie hübsch es doch sein müßte, die herrlichen Blumen draußen auf dem Schlosse des Königs tanzen zu sehen.
Rasch jetzt, wir haben keine Zeit zu verlieren, Hadschar und auch Hadschr AZ-500 Echte Fragen oder Chadschr, Man sammelt Erfahrungen dabei, Ihr Zwillingsbruder stand da, als wäre er aus Stein gehauen, und erwiderte ihren Blick nicht.
Er konnte unmöglich erst eine halbe Stunde hier sein eine Stunde AZ-500 Prüfungsvorbereitung eineinhalb Stunden Harrys Magen fing an zu rumoren, als die Uhr halb eins zeigte, schцnste Gцttin meiner Wahl!
Als ich am Morgen aus dem Fenster schaute, sah AZ-500 Echte Fragen ich nichts als dichten Nebel, Eine kleine Tür aus dünneren, verschlungenen Gitterstäben stand offen, Ich spürte ein leichtes Unwohlsein AZ-500 Simulationsfragen in der Magengrube, aber ich wollte mich auf keinen Fall so zimperlich anstellen wie sonst.
AZ-500 examkiller gültige Ausbildung Dumps & AZ-500 Prüfung Überprüfung Torrents
NEW QUESTION: 1
You have a virtual network named VNET1 that contains the subnets shown in the following table:
You have two Azure virtual machines that have the network configurations shown in the following table:
For NSG1, you create the inbound security rule shown in the following table:
For NSG2, you create the inbound security rule shown in the following table:
For each of the following statements, select Yes if the statement is true. Otherwise, select No.
NOTE: Each correct selection is worth one point.
Answer:
Explanation:
Explanation
Box 1: Yes
The inbound security rule for NSG1 allows TCP port 1433 from 10.10.2.0/24 (or Subnet2 where VM2 and VM3 are located) to 10.10.1.0/24 (or Subnet1 where VM1 is located) while the inbound security rule for NSG2 blocks TCP port 1433 from 10.10.2.5 (or VM2) to 10.10.1.5 (or VM1). However, the NSG1 rule has a higher priority (or lower value) than the NSG2 rule.
Box 2: Yes
No rule explicitly blocks communication from VM1. The default rules, which allow communication, are thus applied.
Box 3: Yes
No rule explicitly blocks communication between VM2 and VM3 which are both on Subnet2. The default rules, which allow communication, are thus applied.
Reference:
https://docs.microsoft.com/en-us/azure/virtual-network/security-overview
NEW QUESTION: 2
Instructions
For both the Router and the Switch the simulated console mode needs to start and remain in enabled mode.
RouterA and SwitchA have been configured to operate in a private network which will connect to the Internet. You have been asked to review the configuration prior to cabling and implementation.
This task requires the use of various IOS commands to access and inspect the running configuration of RouterA and SwitchA. No configuration changes are necessary.
You will connect to RouterA and SwilchA via the console devices that are attached to each.
There are 4 multiple-choice questions with this task. Be sure to answer all of them before leaving this item.
In order to score the maximum points you will need to have accessed both SwitchA and RouterA.
NOTE: The configuration command has been disabled for both the router and switch in this simulation.
Which two of the following are true regarding the configuration of RouterA? (Choose two.)
A. since DHCP is not used on Fa0/1 there is no need to use the NAT protocol
B. at least 5 simultaneous remote connections are possible
C. only telnet protocol connections to RouterA are supported
D. console line connections will never time out due to inactivity
E. remote connections to RouterA using telnet will succeed
Answer: B,E
Explanation:
Explanation/Reference:
Explanation:
Here is the RouterA configuration:
for Router
!
!
no service password-encryption
!
hostname Router1
enable secret 5 $1$14mlkm52....
ip domain-name cisco.com
ip ssh version 2
!
!
username ciscouser password 0 cisco
banner login
- c
!
line con 0
password cisco
line vty 0 4
password 4thfcvcf
no login
transport input telnet ssh
for switch
!
!
no service password-encryption
!
hostname switch1
enable password cisco
username ciscouser password 0 cisco
ip domain-name cisco.com
banner login Review: - These c
!
line con 0
password cisco
line vty 0 4
password 4thfcvcf
no login
transport input telnet ssh
for switch
!
!
no service password-encryption
!
hostname switch1
enable password cisco
username ciscouser password 0 cisco
ip domain-name cisco.com
banner login dumps are valid, I passed this c
!
line con 0
password cisco
line vty 0 4
password 4thfcvcf
no login
transport input telnet ssh
for switch
!
!
no service password-encryption
!
hostname switch1
enable password cisco
username ciscouser password 0 cisco
ip domain-name cisco.com
banner login exam. All simulations and theory questions came from here. You can rely totally on these c
!
line con 0
password cisco
line vty 0 4
password 4thfcvcf
no login
transport input telnet ssh
for switch
!
!
no service password-encryption
!
hostname switch1
enable password cisco
username ciscouser password 0 cisco
ip domain-name cisco.com
banner login dumps.Perry
- Glad to find Braindumpsqa to provide me the latest dumps, finally pass the
c
!
line con 0
password cisco
line vty 0 4
password 4thfcvcf
no login
transport input telnet ssh
for switch
!
!
no service password-encryption
!
hostname switch1
enable password cisco
username ciscouser password 0 cisco
ip domain-name cisco.com
banner login exam, really help in time.Stan
- After choose the c
!
line con 0
password cisco
line vty 0 4
password 4thfcvcf
no login
transport input telnet ssh
for switch
!
!
no service password-encryption
!
hostname switch1
enable password cisco
username ciscouser password 0 cisco
ip domain-name cisco.com
banner login exam materials to prepare for my exam, not only will I pass any c
!
line con 0
password cisco
line vty 0 4
password 4thfcvcf
no login
transport input telnet ssh
for switch
!
!
no service password-encryption
!
hostname switch1
enable password cisco
username ciscouser password 0 cisco
ip domain-name cisco.com
banner login test but also got a good grades!William
-
9.6 / 10 - 315 reviews
-
Disclaimer Policy
The site does not guarantee the content of the comments. Because of the different time and the changes in the scope of the exam, it can produce different effect. Before you purchase the dump, please carefully read the product introduction from the page. In addition, please be advised the site will not be responsible for the content of the comments and contradictions between users. " }, "mpn": "c
!
line con 0
password cisco
line vty 0 4
password 4thfcvcf
no login
transport input telnet ssh
for switch
!
!
no service password-encryption
!
hostname switch1
enable password cisco
username ciscouser password 0 cisco
ip domain-name cisco.com
banner login ", "aggregateRating": { "@type": "AggregateRating", "ratingValue": "4.6", "reviewCount": "810" }, "image": "https://www.braindumpsqa.com/_/bsqa/imgs/product.jpg", "name": "c
line con 0
line vty 0 4
login login local
transport input ssh
line vty 5 15
login local
transport input ssh
A is correct as we can telnet from line 0 to line 4 (line vty o 4).
We can use both telnet and SSH to connect to this router (transport input telnet ssh) -> B is not correct.
C is correct as we can telnet to it.
D is not correct because by default, the timeout is set to 10 minutes on both the console and the vty ports.
E is not correct as NAT can be used even DHCP is not used.NEW QUESTION: 3
Which statement describes a result of securing the Cisco IOS image using the Cisco IOS image resilience feature?
A. The running Cisco IOS image is encrypted and then automatically backed up to a TFTP server.
B. The Cisco IOS image file is not visible in the output from the show flash command.
C. The running Cisco IOS image is encrypted and then automatically backed up to the NVRAM.
D. When the router boots up, the Cisco IOS image is loaded from a secured FTP location.
E. The show version command does not show the Cisco IOS image file location.
Answer: B
Explanation:
http://www.cisco.com/en/US/docs/ios/security/command/reference/sec_book.html
secure boot-config
To take a snapshot of the router running configuration and securely archive it in persistent storage,
use the secure boot-config command in global configuration mode. To remove the secure
configuration archive and disable configuration resilience, use the no form of this command.
secure boot-config [restore filename]
no secure boot-config
Usage Guidelines
Without any parameters, this command takes a snapshot of the router running configuration and
securely archives it in persistent storage. Like the image, the configuration archive is hidden and
cannot be viewed or removed directly from the command-line interface (CLI) prompt . It is
recommended that you run this command after the router has been fully configured to reach a
steady state of operation and the running configuration is considered complete for a restoration, if
required. A syslog message is printed on the console notifying the user of configuration resilience activation. The secure archive uses the time of creation as its filename. For example, .runcfg20020616-081702.ar was created July 16 2002 at 8:17:02. The restore option reproduces a copy of the secure configuration archive as the supplied filename (disk0:running-config, slot1:runcfg, and so on). The restore operation will work only if configuration resilience is enabled. The number of restored copies that can be created is unlimited.
The no form of this command removes the secure configuration archive and disables configuration resilience. An enable, disable, enable sequence has the effect of upgrading the configuration archive if any changes were made to the running configuration since the last time the feature was disabled. The configuration upgrade scenario is similar to an image upgrade. The feature detects a different version of Cisco IOS and notifies the user of a version mismatch. The same command can be run to upgrade the configuration archive to a newer version after new configuration commands corresponding to features in the new image have been issued. The correct sequence of steps to upgrade the configuration archive after an image upgrade is as follows:
Configure new commands
Issue the secure boot-config command secure boot-image To enable Cisco IOS image resilience, use the secure boot-image command in global configuration mode. To disable Cisco IOS image resilience and release the secured image so that it can be safely removed, use the no form of this command.
secure boot-image no secure boot-image Usage Guidelines This command enables or disables the securing of the running Cisco IOS image. The following two possible scenarios exist with this command.
When turned on for the first time, the running image (as displayed in the show version command
output) is secured, and a syslog entry is generated. This command will function properly only
when the system is configured to run an image from a disk with an Advanced Technology
Attachment (ATA) interface. Images booted from a TFTP server cannot be secured. Because this
command has the effect of "hiding" the running image, the image file will not be included in any
directory listing of the disk. The no form of this command releases the image so that it can be
safely removed.
If the router is configured to boot up with Cisco IOS resilience and an image with a different
version of Cisco IOS is detected, a message similar to the following is displayed at bootup:
ios resilience :Archived image and configuration version 12.2 differs from running version 12.3.
Run secure boot-config and image commands to upgrade archives to running version.
To upgrade the image archive to the new running image, reenter this command from the console.
A message will be displayed about the upgraded image. The old image is released and will be
visible in the dir command output.NEW QUESTION: 4
c
DRAG DROP
You administer a Microsoft SQL Server database. Service accounts for SQL Agent are configured to use a local user.
A Microsoft SQL Server Integration Services (SSIS) job step has been created within a SQL Server Agent job.
The SSIS package accesses a network share when exporting data from a SQL Server database.
When you execute the SQL Server Agent job, it fails due to a permissions failure on a share on a remote server.
You need to ensure that the SQL Server Agent job can execute the SSIS package.
Which four actions should you perform in sequence? (To answer, move the appropriate actions from the list of actions to the answer area and arrange them in the correct order.) Select and Place:
Answer:
Explanation:
Explanation/Reference:
Explanation:
SQL Server Agent allows creating a proxy account which defines the security context for the job step.
We need to do is to create a credential to be used by the proxy account.
The created proxy need to have access to the SSIS subsystem
References: https://www.mssqltips.com/sqlservertip/2163/running-a-ssis-package-from-sql-server-agent- using-a-proxy-account/
!
line con 0
password cisco
line vty 0 4
password 4thfcvcf
no login
transport input telnet ssh
for switch
!
!
no service password-encryption
!
hostname switch1
enable password cisco
username ciscouser password 0 cisco
ip domain-name cisco.com
banner login Exam", "sku": "c
!
line con 0
password cisco
line vty 0 4
password 4thfcvcf
no login
transport input telnet ssh
for switch
!
!
no service password-encryption
!
hostname switch1
enable password cisco
username ciscouser password 0 cisco
ip domain-name cisco.com
banner login ", "description": "c
line con 0
line vty 0 4
login login local
transport input ssh
line vty 5 15
login local
transport input ssh
A is correct as we can telnet from line 0 to line 4 (line vty o 4).
We can use both telnet and SSH to connect to this router (transport input telnet ssh) -> B is not correct.
C is correct as we can telnet to it.
D is not correct because by default, the timeout is set to 10 minutes on both the console and the vty ports.
E is not correct as NAT can be used even DHCP is not used.NEW QUESTION: 3
Which statement describes a result of securing the Cisco IOS image using the Cisco IOS image resilience feature?
A. The running Cisco IOS image is encrypted and then automatically backed up to a TFTP server.
B. The Cisco IOS image file is not visible in the output from the show flash command.
C. The running Cisco IOS image is encrypted and then automatically backed up to the NVRAM.
D. When the router boots up, the Cisco IOS image is loaded from a secured FTP location.
E. The show version command does not show the Cisco IOS image file location.
Answer: B
Explanation:
http://www.cisco.com/en/US/docs/ios/security/command/reference/sec_book.html
secure boot-config
To take a snapshot of the router running configuration and securely archive it in persistent storage,
use the secure boot-config command in global configuration mode. To remove the secure
configuration archive and disable configuration resilience, use the no form of this command.
secure boot-config [restore filename]
no secure boot-config
Usage Guidelines
Without any parameters, this command takes a snapshot of the router running configuration and
securely archives it in persistent storage. Like the image, the configuration archive is hidden and
cannot be viewed or removed directly from the command-line interface (CLI) prompt . It is
recommended that you run this command after the router has been fully configured to reach a
steady state of operation and the running configuration is considered complete for a restoration, if
required. A syslog message is printed on the console notifying the user of configuration resilience activation. The secure archive uses the time of creation as its filename. For example, .runcfg20020616-081702.ar was created July 16 2002 at 8:17:02. The restore option reproduces a copy of the secure configuration archive as the supplied filename (disk0:running-config, slot1:runcfg, and so on). The restore operation will work only if configuration resilience is enabled. The number of restored copies that can be created is unlimited.
The no form of this command removes the secure configuration archive and disables configuration resilience. An enable, disable, enable sequence has the effect of upgrading the configuration archive if any changes were made to the running configuration since the last time the feature was disabled. The configuration upgrade scenario is similar to an image upgrade. The feature detects a different version of Cisco IOS and notifies the user of a version mismatch. The same command can be run to upgrade the configuration archive to a newer version after new configuration commands corresponding to features in the new image have been issued. The correct sequence of steps to upgrade the configuration archive after an image upgrade is as follows:
Configure new commands
Issue the secure boot-config command secure boot-image To enable Cisco IOS image resilience, use the secure boot-image command in global configuration mode. To disable Cisco IOS image resilience and release the secured image so that it can be safely removed, use the no form of this command.
secure boot-image no secure boot-image Usage Guidelines This command enables or disables the securing of the running Cisco IOS image. The following two possible scenarios exist with this command.
When turned on for the first time, the running image (as displayed in the show version command
output) is secured, and a syslog entry is generated. This command will function properly only
when the system is configured to run an image from a disk with an Advanced Technology
Attachment (ATA) interface. Images booted from a TFTP server cannot be secured. Because this
command has the effect of "hiding" the running image, the image file will not be included in any
directory listing of the disk. The no form of this command releases the image so that it can be
safely removed.
If the router is configured to boot up with Cisco IOS resilience and an image with a different
version of Cisco IOS is detected, a message similar to the following is displayed at bootup:
ios resilience :Archived image and configuration version 12.2 differs from running version 12.3.
Run secure boot-config and image commands to upgrade archives to running version.
To upgrade the image archive to the new running image, reenter this command from the console.
A message will be displayed about the upgraded image. The old image is released and will be
visible in the dir command output.NEW QUESTION: 4
c
DRAG DROP
You administer a Microsoft SQL Server database. Service accounts for SQL Agent are configured to use a local user.
A Microsoft SQL Server Integration Services (SSIS) job step has been created within a SQL Server Agent job.
The SSIS package accesses a network share when exporting data from a SQL Server database.
When you execute the SQL Server Agent job, it fails due to a permissions failure on a share on a remote server.
You need to ensure that the SQL Server Agent job can execute the SSIS package.
Which four actions should you perform in sequence? (To answer, move the appropriate actions from the list of actions to the answer area and arrange them in the correct order.) Select and Place:
Answer:
Explanation:
Explanation/Reference:
Explanation:
SQL Server Agent allows creating a proxy account which defines the security context for the job step.
We need to do is to create a credential to be used by the proxy account.
The created proxy need to have access to the SSIS subsystem
References: https://www.mssqltips.com/sqlservertip/2163/running-a-ssis-package-from-sql-server-agent- using-a-proxy-account/
************ welcome to router1 If you encountered any problem, please consult the administrator
************* Certification - c
!
line con 0
password cisco
line vty 0 4
password 4thfcvcf
no login
transport input telnet ssh
for switch
!
!
no service password-encryption
!
hostname switch1
enable password cisco
username ciscouser password 0 cisco
ip domain-name cisco.com
banner login Exam Braindumps", "releaseDate": "Apr 02, 2019", "offers": { "@type": "Offer", "availability": "http://schema.org/InStock", "url": "https://www.braindumpsqa.com/c
!
line con 0
password cisco
line vty 0 4
password 4thfcvcf
no login
transport input telnet ssh
for switch
!
!
no service password-encryption
!
hostname switch1
enable password cisco
username ciscouser password 0 cisco
ip domain-name cisco.com
banner login _braindumps.html", "priceValidUntil": "2021-04-04", "price": "49.98", "priceCurrency": "USD" }, "review": [{ "@type": "Review", "author": "Guest", "datePublished": "Apr 04, 2019", "description": "c
!
line con 0
password cisco
line vty 0 4
password 4thfcvcf
no login
transport input telnet ssh
for switch
!
!
no service password-encryption
!
hostname switch1
enable password cisco
username ciscouser password 0 cisco
ip domain-name cisco.com
banner login dumps still valid!", "reviewRating": { "@type": "Rating", "bestRating": "5", "ratingValue": "5", "worstRating": "0" } }] }
- Contact US:
-
support@braindumpsqa.com
- Popular Vendors
- Adobe
- Alcatel-Lucent
- Avaya
- BEA
- CheckPoint
- CIW
- CompTIA
- CWNP
- EC-COUNCIL
- EMC
- EXIN
- Hitachi
- HP
- ISC
- ISEB
- Juniper
- Lpi
- Network Appliance
- Nortel
- Novell
- Polycom
- SASInstitute
- Why Choose Sugakumaster Testing Engine
Quality and ValueSugakumaster Practice Exams are
written to the highest standards of technical accuracy, using only certified subject matter experts
and published authors for development - no all study materials.
Tested and ApprovedWe are committed to the process
of vendor and third party approvals. We believe professionals and executives alike deserve the
confidence of quality coverage these authorizations provide.
Easy to PassIf you prepare for the exams using our
Sugakumaster testing engine, It is easy to succeed for all certifications in the first attempt. You
don't have to deal with all dumps or any free torrent / rapidshare all stuff.
Try Before BuySugakumaster offers free demo of each
product. You can check out the interface, question quality and usability of our practice exams
before you decide to buy.
